Canso or PBY Catalina rear fuselage access replacing gun blisters (4 Viewers)

yduwelz

Airman
10
3
Joined
Jul 23, 2010
Canso or PBY Catalina rear fuselage access metal sheets replacing gun blisters

Hello,

I am searching for a drawing of the replacement sheet metal used the replace the rear fuselage blisters on civil version of Canso/catalina.

panneau12b.jpg

panneaux2.jpg


I plan to make a scale model of a catalina used in the past by the French Sécurité Civile and some aircraft of this organisation were modified in Canada this way.

Many thanks in advance
 
For the installation in your photo you probably need to track down all the FAA Supplemental Type Certificates for the Consolidated type 28 as your starting point and then see which Certificate holders still exist. You MAY be able to get STC copies from the FAA.
 
Canso or PBY Catalina rear fuselage access metal sheets replacing gun blisters

Hello,

I am searching for a drawing of the replacement sheet metal used the replace the rear fuselage blisters on civil version of Canso/catalina.

View attachment 903928
View attachment 903929

I plan to make a scale model of a catalina used in the past by the French Sécurité Civile and some aircraft of this organisation were modified in Canada this way.

Many thanks in advance
This is a 100% Canadian post-war modification as seen on several Cansos (those are amphibians only). The modifications were done by Aircraft Industries Limited around 1951.
I have similar photos of different birds. In your photo IMHO that a/c has been used for some geodetic measurements (the boom under the tail is some kind of a radar).
Here some examples of modified Cansos (check modified nose as well):
Canso 1.jpg

Canso 2.jpg

Canso 3.jpg

Canso 4.jpg

Canso 5.jpg

This IMHO is the same mod without the half-spherical window in the middle of the hatch. Note the fairing over the original opening - this is the lighter area in the above photos:
Canso 6.jpg

I don't have any drawings but I will check my archive for all Canso-articles and photos.
Source of photos: here.
Cheers!
 
This is a 100% Canadian post-war modification as seen on several Cansos (those are amphibians only). The modifications were done by Aircraft Industries Limited around 1951.
I have similar photos of different birds. In your photo IMHO that a/c has been used for some geodetic measurements (the boom under the tail is some kind of a radar).
Here some examples of modified Cansos (check modified nose as well):
View attachment 904051
View attachment 904052
View attachment 904053
View attachment 904054
View attachment 904050
This IMHO is the same mod without the half-spherical window in the middle of the hatch. Note the fairing over the original opening - this is the lighter area in the above photos:
View attachment 904049
I don't have any drawings but I will check my archive for all Canso-articles and photos.
Source of photos: here.
Cheers!
Thank you, exactly the illustrations of what drawings I am looking for. Regards
 
Geoterrex, if they still exist, may have the drawings as the lower aircraft in post 1 is one of theirs.
 
Did the RCAF fit B-25 powerplants to their Canso aircraft? The Geoterrix aircraft had those and other mods. To me the RCAF doors look very tidy and 'professional' while the Geoterrix doors do not.
AFAIK the original mods didn't include engine changes. But...and here's the but, several of those modified RCAF Cansos have been modified again and again. I have chosen photos with the original mods from the early 50s. If you go and check the link I posted you'll find many of those being modified again as water bombers and whatnot. Change of engines is quite possible in a later phase for the same airplanes.
That's my point exactly: the hatches with sliding doors are RCAF mods from the early 50s. Any later changes were probably done by others and the civil users did not modify the original blisters.
 
This was at American Aero some years ago. Not sure where it went.

Tony
 

Attachments

  • 20171030_112731.jpg
    20171030_112731.jpg
    1.4 MB · Views: 9
  • 20171030_112530.jpg
    20171030_112530.jpg
    372.1 KB · Views: 9
This was at American Aero some years ago. Not sure where it went.

Tony
C-FPQK is a Canso-A serial 9830. This particular a/c had longer military history with RCAF, until the 1960s. Later on it was sold to Department of Lands and Forests, Province of Quebec, operated as tanker "12". To civil register as CF-PQK. Still airworthy with Quebec in 1976, registered as C-FPQK by 1980. Sold to Foundation Aerovision of St. Hubert, Quebec on 1 June 1994, latest Certificate of Registration issued on 18 May 1998 as C-FPQK.
Used as a SAR-airplane the blisters remained longer than with the other planes, quoted earlier.
Screenshot 2026-11-21 at 22-10-44 Consolidated Canso.png

It is possible that the hatch in your photos is of a different type though (not a sliding one). Below a photo of a different Canso with a "civil type" of hatch:
Canso hatch.png
 
Thank you, exactly the illustrations of what drawings I am looking for. Regards
Check Canso serial 11093 from the site I posted before.
It's still existing with the modifications you are looking for. There are enough photos IMHO to use them for a model and scratch build the mods.
Cheers!
 

Users who are viewing this thread

Back