Pratt & Whitney R-2800/ Hamilton Standard Hydromatic Prop Removal Help Needed (2 Viewers)

AABEECK

Recruit
5
3
Joined
Nov 11, 2026
I have to remove a pair of Hydromatic Hamilton Standard props from the R2800 engines. I am trying to find what specific tools are needed to remove the props. I have found a list online of all the tools needed for taking the props off and apart. I need to know what tool or tools are needed once the dome is off? Any assistance is greatly appreciated as I want to be able to show up with everything needed on hand to do the job. Thank you.
 
Welcome to the forum. A little about your self and the aircraft you are working on would be welcomed by most members.

If you go to the thread Manual Index - American any Erection and Maintenance manual for any aircraft that has Hydromatic props will give you the details you need. Note there is a locking screw that must be removed before you can undo the dome retaining ring.

Today I am getting an error message for every link from the above web page. Had that problem not existed I would have given you a specific link.
 
Last edited:
Welcome to the forum. A little about your self and the aircraft you are working on would be welcomed by most members.

If you go to the thread Manual Index - American any Erection and Maintenance manual for an aircraft that has Hydromatic props will give you the details you need. Note there is a locking screw that must be removed before you can undo the dome retaining ring.

Today I am getting an error message for every link from the above web page. Had that problem not existed I would have given you a specific link.
Thank you I will take a look. I am actually removing engines and props from a newer aircraft, but since these were common engines across older models I thought I would try here. Fairchild C123K, Aerial Visuals - Airframe Dossier - Chase C-123K Provider, s/n PNP-022 PNP, c/n 20144, c/r N8190B
 
Thanks for the background. A nice addition to the collection.
 
she appears rudderless in that last photo. It is a common problem to get rudder damage in storage. I know it was put to rights and ferried to the new home, but I wanted to comment on that.
It is hard to block them both top and bottom and a big wind exerts so much force across the rudder in an unnatural way.
 
The C123 props look similar to the Canadair CL-215, 43E60's. The basic order from memory is remove the dome cap and remove flyweights if installed, and then the oil tube. Remove locking screw from the dome nut, and then the dome. Remove the serrated locking piece that goes between shaft nut and the oil transfer unit, you will need a 10-32 screw to get the lock out, after removing the locking ring. Remove oil transfer unit, you would need the long round wrench with the internal serrations. There may be a locking pin on a thin metal strip that goes through the inside of the engine shaft into the propeller retaining nut. You would then need the long round wrench with the external serrations to remove the propeller retaining nut. This is a very high torque nut, so you may need a torque reducer to break it loose. Wind the shaft nut out until you break the propeller loose from the cones,.
 
If the engines were ever run with those props on there, be prepared for lots of oil coming out of the dome and have several big buckets on hand and a way to suppor them before you crack anything loose.... BTDT and had to clean up the mess.... :banghead:

The dome is very heavy and really should be a two man operation during removal. You will also need a pair of long endless slings to crane the props off.
 
This place is amazing.
 
Like Maty I thought that the props were the 23E50 series used on most US WW2 aircraft but as the prop expert here believes them to be 43E60's and that is a whole different ball game as those are a reversing propellor.

My suggestion for A AABEECK is to get a monthly membership to Register | AirCorps Library as they have a good selection of 43E60 documents that you can view on line so you can read the manual on your phone as you work. The monthly cost is low and you can cancel any time.

1794815923882.png


1794815826246.png
 
Last edited:
43E60 works out to be a Mod 4 hub, 3 blades, E sized blade shank, for installation on an SAE 60 shaft...
 
I have to remove a pair of Hydromatic Hamilton Standard props from the R2800 engines. I am trying to find what specific tools are needed to remove the props. I have found a list online of all the tools needed for taking the props off and apart. I need to know what tool or tools are needed once the dome is off? Any assistance is greatly appreciated as I want to be able to show up with everything needed on hand to do the job. Thank you.
We have pulled our C-123 props several times... The 123 manual will give you all you need. Their removal is very straight forward. But, they are heavy... and messy.

While I have you. Air Heritage Museum in Beaver Falls, PA still flies a C-123! Yes, we have been operating one of the last flyable C-123's for over 20 years!!! The propellers are currently out for O/H at H&S in Detroit. Right engine is at Anderson for MOH... Airframe is in our hangar for some TLC.

If you are removing the 2800's and propellers and scraping the airframe, AIR HERITAGE would be interesting in any parts you don't want.... 724-843-2820 10-5p M-Sat. Cheers'
 
We have pulled our C-123 props several times... The 123 manual will give you all you need. Their removal is very straight forward. But, they are heavy... and messy.

While I have you. Air Heritage Museum in Beaver Falls, PA still flies a C-123! Yes, we have been operating one of the last flyable C-123's for over 20 years!!! The propellers are currently out for O/H at H&S in Detroit. Right engine is at Anderson for MOH... Airframe is in our hangar for some TLC.

If you are removing the 2800's and propellers and scraping the airframe, AIR HERITAGE would be interesting in any parts you don't want.... 724-843-2820 10-5p M-Sat. Cheers'
Thank you, I have been following your C-123 on Facebook. This C-123 was being sold for scrap and I wanted to save the engines and props. The day after I bought them someone else bought the airframe keeping from the shears and plans to turn it into a bed and breakfast. I will pass along your information to them.
 
I have been able to track down the part numbers of the needed tools, I am still trying to physically locate an HSP1461 or HSP1891 in case anyone has one gathering dust. Thanks everyone. Will update once these are off the plane and on a run stand. Just found out based on the yellow tag that one of the engines has about 11hrs SMOH. Still looking for info on the other one.
 
Last edited:
Here is the HS Manual for your 43E60's. Re-check your tool HSP 1461.. I think it is HSP "1460". Your HSP 1891 is correct.


We have a whole list of parts from your 123 that we could use... Currently, we are looking for Cowl Flap Cables... among many other "Un-obtainium" parts...... let's talk!
 
Here is the HS Manual for your 43E60's. Re-check your tool HSP 1461.. I think it is HSP "1460". Your HSP 1891 is correct.


We have a whole list of parts from your 123 that we could use... Currently, we are looking for Cowl Flap Cables... among many other "Un-obtainium" parts...... let's talk!
I already have the 1460, the 1461 is a variant of the 1891 with the same tooth count and diameter, one is for the use with torque multiplier and the other is just a straight bar(so I have been told, and the pictures look correct). Will pass your info to the airframe owner, he is not moving it until spring, so it will be awhile.
 
We have/use the Torque Multiplier on the C-123 props.... I will look, but I think we have all three HS tools. I'm more proficient on the 23E50's (C-47) that we also fly.
 

Users who are viewing this thread

Back