Armour Plate for Avro Lancaster (1 Viewer)

[Allan Hunter]

I'd be interested to know what those with more knowledge than I have will say. I read somewhere that 'Bomber' Harris ordered armor plate stripped from Lancasters as the war went on, so the weight or bombs could be increased. This plate would therefore be from an early model?

 

[ThomasP]

As far as I know the Lancaster carried most of its armour for the entire war. Which particular plate you are referring to?

 

[Airframes]

There were most likely exceptions, but as far as I know, the only armour plate in the Lanc was the pilot's seat back armour, with the armoured doors at the main spar location being removed or deleted.

 

[ThomasP]

My understanding is that there were armour plates protecting the navigator's and radio operator's stations as well, plus armour apron plates in the upper and rear turrets. So a full mid-war 'standard' armour fit would be the pilot's seat back armour, the armoured bulkhead behind the pilot's compartment, the armour plates behind the navigator's and radio operator's stations and the apron armour plate in the turrets.

The 'standard' armour plate outfit is indicated in red in the dwg below. The numerical indicators are #86/129/139. (I think I have it marked correctly, but not 100% sure.)

 

[Greyman]

I've posted this elsewhere but worth reposting here:

As introduced -- the Lancaster had:

Pilot
28 lb (4 mm) seat back
27 lb (9 mm) head piece

Flight Engineer
?? lb (2.5 in) armoured glass

W/T Op and Navigator position
160 lb (7 mm) *another source has 6 mm*

W/T Op seat back
13 lb (4 mm)

Mid-upper turret (FN50)
26 lb (6 mm)
38 lb (10 ga dural)

Rear turret (FN20)
45 lb (9 mm)
8 lb (6 mm)

Engine coverings
144 lb (10 swg)

Engines + ancillary
100 lb (8 mm)

Unsure, but I think the above 100 lb of armour consisted of:

- crescent-shaped plate which protects the oil tank sump​

- vertical piece of plating behind the header tank leg
- vertical plate at the side of the radiator at outboard engines​

 

[HP52]

I've posted this elsewhere but worth reposting here:

As introduced -- the Lancaster had:

Pilot
28 lb (4 mm) seat back
27 lb (9 mm) head piece

Flight Engineer
?? lb (2.5 in) armoured glass

W/T Op and Navigator position
160 lb (7 mm) *another source has 6 mm*

W/T Op seat back
13 lb (4 mm)

Mid-upper turret (FN50)
26 lb (6 mm)
38 lb (10 ga dural)

Rear turret (FN20)
45 lb (9 mm)
8 lb (6 mm)

Engine coverings
144 lb (10 swg)

Engines + ancillary
100 lb (8 mm)

Unsure, but I think the above 100 lb of armour consisted of:

- crescent-shaped plate which protects the oil tank sump
- vertical piece of plating behind the header tank leg
- vertical plate at the side of the radiator at outboard engines​

I had no idea they had so much armour. The Old Man had a lot of time for the 13mm MG 131. He had a Lanc back one night - it had a 13mm entry hole near the back of the A/C and he could sight through its complete passage through panels and bulkheads until exiting up neat the nose - except that it was 463 Sqn - I have no other details. He was always pretty dry but didn't embellish his stories and rarely told the same one twice.

 

[Allan Hunter]

I've posted this elsewhere but worth reposting here:

As introduced -- the Lancaster had:

Pilot
28 lb (4 mm) seat back
27 lb (9 mm) head piece

Flight Engineer
?? lb (2.5 in) armoured glass

W/T Op and Navigator position
160 lb (7 mm) *another source has 6 mm*

W/T Op seat back
13 lb (4 mm)

Mid-upper turret (FN50)
26 lb (6 mm)
38 lb (10 ga dural)

Rear turret (FN20)
45 lb (9 mm)
8 lb (6 mm)

Engine coverings
144 lb (10 swg)

Engines + ancillary
100 lb (8 mm)

Unsure, but I think the above 100 lb of armour consisted of:

- crescent-shaped plate which protects the oil tank sump
- vertical piece of plating behind the header tank leg
- vertical plate at the side of the radiator at outboard engines​

This is all very interesting. So some 500 pounds plus of armor was on the original Lancaster, but eventually this was reduced to just the segment behind the pilot's seat -- if I'm understanding these responses correctly? I wonder when the order was sent to the squadrons?

 

[Greyman]

I've heard a few times about armour being reduced to just the pilot's bit -- but just from things people say, nothing concrete.

If that is the case I assume it would have been a gradual process.

 

[ThomasP]

I have always suspected that any such idea to remove most or all the armour was a sentiment expressed by someone at the time, but never became an actual order. I have seen images of Lancaster turrets at the end of the war with the armour aprons still in place, as well as the pilot seat armour. There was also usually at least one of the armour plates at the navigator/radio operator station as well (you can see the armour plate markings on the bulkhead behind the radios).

Plus, I do not think it would make any sense to give such an order. 500 lbs plus of minus will not make any significant difference to 90%? (95%? 99%?) of the missions they flew.

At some point in time (end of 1942?) an amour increase kit (Mod.439) became available that weighed somewhere in the neighborhood of 1700 lbs. The 1700 lbs was in addition to most of what was already in use as the time. It was S.O.O. (Special Order Only), and I do not know how often it was ordered. That much weight of armour I can see being deemed a detriment to the mission re the mindset of some of the high command.