Question about TA-152H MBG cutoff system (1 Viewer)

rocaf2003

Airman
16
1
Joined
Oct 8, 2025
Hi,There,I have a question of the MBG emergency handle of TA152H.By the end of the war, were all TA-152H fighters actually equipped with the MBG (Motorbediengerät) cut-off system? In other words, was that red MBG emergency handle actually functional on every TA-152H?
 
The Motorbediengerät was an integral accessory of the Jumo 213 engine and couldn't be removed or replaced neither entirely nor partially. So the red Notzug handle being a part of the device was still there. However, the reality of whether pilots could freely use it in combat was a completely different matter.
Towards the end of the war, the quality of metal alloys used in engine construction deteriorated drastically due to a shortage of raw materials. Forcing the Jumo 213E engine to operate without the precise assistance of the MBG system created an immediate risk of engine damaging. Consequently, mechanics in units frequently installed wire seals on the Notzug control. Pilots were permitted to break this seal only in situations of extreme mortal danger. What is more , it seems that using of the dedicated MW 50 system was more safer. This injection cooled the combustion chambers, allowing engine power to be increased without risking structural failure. This rendered the use of the mechanical Notzug override completely pointless in a functional aircraft. IMHO E Engineman may add much more.
 
The Motorbediengerät was an integral accessory of the Jumo 213 engine and couldn't be removed or replaced neither entirely nor partially. So the red Notzug handle being a part of the device was still there. However, the reality of whether pilots could freely use it in combat was a completely different matter.
Towards the end of the war, the quality of metal alloys used in engine construction deteriorated drastically due to a shortage of raw materials. Forcing the Jumo 213E engine to operate without the precise assistance of the MBG system created an immediate risk of engine damaging. Consequently, mechanics in units frequently installed wire seals on the Notzug control. Pilots were permitted to break this seal only in situations of extreme mortal danger. What is more , it seems that using of the dedicated MW 50 system was more safer. This injection cooled the combustion chambers, allowing engine power to be increased without risking structural failure. This rendered the use of the mechanical Notzug override completely pointless in a functional aircraft. IMHO E Engineman may add much more.
Appreciate for your help,Sir!You mentioned that the mechanics installed wire seals on the "Notzug" control device, which is quite useful to me. It is said that once the "Notzug" handle is pulled out, the MBG will no longer control the engine; instead, a separate backup control system will take over. Given the supply shortages in Germany at the end of the war, was this backup control system actually installed on every single TA 152 H?
 
Actually the Notzug option wasn't the cut-off switch. It was a kind of engine boost. Using of the handle allowed to get a temporary exceeding of standard boost pressure limits and the attainment of maximum power. Under the normal conditions, the MBG automatically managed the engine parameters with just a single throttle lever only. I'm not sure but it seems the MBG didn't have backup control system in the sense that there were two devices. There was the mechanical emergency override system called Notsteuerung allowing to mechanical override of the MBG automatic control system. It was used in the case the MBG failed or if there was an oil pressure failure or a jam in the control system's hydraulics. So the pilot could take control of the engine using direct linkages and pushrods. However it should be kept in mind that the manual control over the Jumo 213 engine wasn't the easy thing. But the lack of the Notsteuerung system would mean the immediate engine shotdown and the loss of the aircraft. For the reason the system was a standard and mandatory technical solution for the Jumo 213 engine.
 
Actually the Notzug option wasn't the cut-off switch. It was a kind of engine boost. Using of the handle allowed to get a temporary exceeding of standard boost pressure limits and the attainment of maximum power. Under the normal conditions, the MBG automatically managed the engine parameters with just a single throttle lever only. I'm not sure but it seems the MBG didn't have backup control system in the sense that there were two devices. There was the mechanical emergency override system called Notsteuerung allowing to mechanical override of the MBG automatic control system. It was used in the case the MBG failed or if there was an oil pressure failure or a jam in the control system's hydraulics. So the pilot could take control of the engine using direct linkages and pushrods. However it should be kept in mind that the manual control over the Jumo 213 engine wasn't the easy thing. But the lack of the Notsteuerung system would mean the immediate engine shotdown and the loss of the aircraft. For the reason the system was a standard and mandatory technical solution for the Jumo 213 engine.
Ah, yes, please forgive my clumsy wording, which stems from a lack of expertise,Sir... What I mean by the so-called "second system" is actually the Notsteuerung system. I would like to ask whether, due to supply issues at the end of the war, Germany was able to install it on every single TA 152 H without exception.
 
Last edited by a moderator:
Ah, yes, please forgive my clumsy wording, which stems from a lack of expertise,Sir... What I mean by the so-called "second system" is actually the Notsteuerung system. I would like to ask whether, due to supply issues at the end of the war, Germany was able to install it on every single TA 152 H without exception.

It is all fine with your wording. So take it easy. :)

And to answer your question. Yes it was mounted on all Ta 152H with the Jumo 213 engine. Both the MBG and the mechanical Notsteuerung system had to be there because it was an emergency system. Without of the system it would be impossible to keep the control over the engine if the MBG failed, and in a result, loosing the plane over the flight. IMHO the lack of the Notsteuerung system would cause the Ta 152H being "disposable". Could you imagine what would happen when the MBG would fail while taking off? Or the MBG would be hit during a dogfight etc ...
 
The Motorbediengerät was an integral accessory of the Jumo 213 engine and couldn't be removed or replaced neither entirely nor partially. So the red Notzug handle being a part of the device was still there. However, the reality of whether pilots could freely use it in combat was a completely different matter.
Towards the end of the war, the quality of metal alloys used in engine construction deteriorated drastically due to a shortage of raw materials. Forcing the Jumo 213E engine to operate without the precise assistance of the MBG system created an immediate risk of engine damaging. Consequently, mechanics in units frequently installed wire seals on the Notzug control. Pilots were permitted to break this seal only in situations of extreme mortal danger. What is more , it seems that using of the dedicated MW 50 system was more safer. This injection cooled the combustion chambers, allowing engine power to be increased without risking structural failure. This rendered the use of the mechanical Notzug override completely pointless in a functional aircraft. IMHO E Engineman may add much more.
Dear Sir,

You mentioned yesterday that "Towards the end of the war, the quality of metal alloys used in engine construction deteriorated drastically due to a shortage of raw materials. Forcing the Jumo 213E engine to operate without the precise assistance of the MBG system created an immediate risk of engine damaging. Consequently, mechanics in units frequently installed wire seals on the Notzug control. Pilots were permitted to break this seal only in situations of extreme mortal danger." However, I have since come across a statement in an operating manual suggesting that during cold-start procedures at low temperatures, pulling out the Notzug lever actually facilitates starting. This leaves me puzzled: since the device appears to be secured by a wire seal in actual practice and is not to be used lightly, would the seal be broken and the Notzug lever pulled out as recommended for cold-starting at low temperatures? I would be most honoured if I could once again receive your expert and patient assistance.
 
In fact, using the Notzug could make a cold engine start easier. To the best of my knowledge, starting the engine with the Notzug lever pulled out was prohibited. The mechanical linkage had to be coupled with the MBG hydraulic automatic unit to ensure the engine did not receive an excessively rich or lean mixture and to prevent a sudden surge in RPM the moment the cylinders fired. For a proper start, the pilot would set the main throttle lever to a specific notch or position marked Anlassen (Start/Idle), the MBG unit would then precisely meter the fuel injected into the cold engine. Certainly the the maintenance teams could have their own tips and tricks but these might not follow the official procedures. Secondly if there was was the wire seals installed on the Notzug lever they just didn't use it rather. What is more, using the metal alloys of the worse quality and the breaking of blockade didn't mean the engine had to be damaged. It seems that the wire seal was more the warning than the blockade. And again it should be highlight that the manual control over the engine without the MBG wasn't the easiest thing and required some of experience at using the proper settings manually. Additionally the Ta 152H is a kite introduced into service in January 1945, So its "life" as a fighter machine wasn't too long. Contrary to this the Fw 190D-9 entered the service in summer 1944. Using the same system for the Jumo engine had them made of the better quality materials than the Ta 152H.
 
In fact, using the Notzug could make a cold engine start easier. To the best of my knowledge, starting the engine with the Notzug lever pulled out was prohibited. The mechanical linkage had to be coupled with the MBG hydraulic automatic unit to ensure the engine did not receive an excessively rich or lean mixture and to prevent a sudden surge in RPM the moment the cylinders fired. For a proper start, the pilot would set the main throttle lever to a specific notch or position marked Anlassen (Start/Idle), the MBG unit would then precisely meter the fuel injected into the cold engine. Certainly the the maintenance teams could have their own tips and tricks but these might not follow the official procedures. Secondly if there was was the wire seals installed on the Notzug lever they just didn't use it rather. What is more, using the metal alloys of the worse quality and the breaking of blockade didn't mean the engine had to be damaged. It seems that the wire seal was more the warning than the blockade. And again it should be highlight that the manual control over the engine without the MBG wasn't the easiest thing and required some of experience at using the proper settings manually. Additionally the Ta 152H is a kite introduced into service in January 1945, So its "life" as a fighter machine wasn't too long. Contrary to this the Fw 190D-9 entered the service in summer 1944. Using the same system for the Jumo engine had them made of the better quality materials than the Ta 152H.

Understood,Sir. That is to say, for an intact aircraft, there is often a wire seal on the Notzug handle. When the aircraft is intact and there are no issues, people do not break it. Only if the MBG fails and the aircraft is no longer intact would they break the wire seal to try to get the aircraft to return or make an emergency landing (at which point the aircraft is no longer intact). May I ask if my understanding is correct,Sir?
 
Understood,Sir. That is to say, for an intact aircraft, there is often a wire seal on the Notzug handle. When the aircraft is intact and there are no issues, people do not break it. Only if the MBG fails and the aircraft is no longer intact would they break the wire seal to try to get the aircraft to return or make an emergency landing (at which point the aircraft is no longer intact). May I ask if my understanding is correct,Sir?


Yes you understood it correct. But a note though. The wire seal on the Notzug lever could be or not. It seems that the installation wasn't the fabric requrement. Just the maintence team could attach it there or not. No matter if the plane was airworthy. The pilot was the one who should remember when the Notzug handle should be used.
 
Yes you understood it correct. But a note though. The wire seal on the Notzug lever could be or not. It seems that the installation wasn't the fabric requrement. Just the maintence team could attach it there or not. No matter if the plane was airworthy. The pilot was the one who should remember when the Notzug handle should be used.
Thank you for your professional and patient assistance, sir. With this, I can confirm that the Notzug handles in the cockpits of all intact aircraft parked on the ground are not in the pulled‑out position. That is sufficient for me.

All my lengthy questions essentially boil down to one point: the Notzug handle will not be pulled out in the cockpit of an intact aircraft. Your help has provided crucial evidence: in some airframes these handles are even secured with wire, let alone being pulled out on an intact aircraft.
 
Hi,There,I have a question of the MBG emergency handle of TA152H.By the end of the war, were all TA-152H fighters actually equipped with the MBG (Motorbediengerät) cut-off system? In other words, was that red MBG emergency handle actually functional on every TA-152H?

Hi, I note that your question is about the Ta 152 H with JUMO 213 E engine and the pull handle for the "NOTZUG fur bediengetriebe" which is a pull control which selects normal AUTOMATIK function of the Motorbediengerate (MBG) motor control when pushed in or, Emergency control function of the MBG motor control when pulled out.
This functionality seems to be similar to that of the earlier JUMO 213A engine and that information is the basis of my understanding. AFAIK, specific information about the later JUMO 213 engine types is very rare.
The engine control system of the JUMO 213 engine family used the MBG control system to give single-lever control of the JUMO 213, combining supercharger gear control, fuel injection pump output control, magneto timing control and the swirl-throttle intake guidevane control. In addittion to the Swirl throttle on the supercharger intake, the engine had a cylindrical plate type throttle for control of inlet airflow at engine start and low power operation when the main Swirl throttle is not effective. This cylindrical plate type throttle is always mechanically linked to the pilots throttle lever position via the MBG. Note, at high power the cylindrical plate type throttle is not effective, the MBG then controls the oil-operated Swirl throttle.

Because the Swirl throttle has a primary effect on airflow into the engine and it is oil operated by the MBG, there are two circumstances where complications arise. The first is if the MBG control function or the Swirl throttle itself is damaged. In this case, the Emergency MBG control is pulled to cut-off the control of the Swirl throttle (its control oil pressure is cut-off). This action allows the Swirl throttle to open, but the pilot must reduce the throttle position to give an absolute maximum of 2700 rpm. This action may allow the engine to keep running being controlled by the cylindrical plate type throttle at low power in an emergency situation where the engine will not run properly in the normal Automatik mode.
The second complication is for engine cold start at temperatures of 0 to minus25 degrees Celsius. At these low temperatures, the control oil to the Swirl throttle control piston is too thick for the Swirl throttle to control the airflow and it prevents successful starting, so the Emergency control lever is pulled before start and the Cylindrical plate throttle alone controls the airflow to allow successful starting. When the engine has started and is running smoothly, the emergency control is returned to the Automatik position and the engine functions normally.

Cheers

Eng
 
Last edited:
Hi Crew,

I thought that I might add a few more details about the JUMO 213 MBG system, as it is not well understood, IMO.
This thread asked about the Emergency control of the MBG, the Motorbediengerat or "engine control system" of the Jumo 213 engines, so here is a little more info from the 213 and 211 Handbuch's.
Junkers previously designed their Jumo 211 engines with mostly WW2 period conventional engine control systems, ie, the Magneto's, fuel mixture, MAP limit control, supercharger gear and propeller pitch (hence engine speed), were all controlled by individual linkages and pressure/temp/rpm sensors within the sub-units. The pilot control of this type of engine system could include throttle, mixture and engine speed controls, sometimes with a supercharger control option. For the Jumo 213 Junkers decided to make the control systems combined into
a single unit-the Motorbediengerat (MBG). The MBG mostly centralised the sensor functions into a single control unit. However, additional linkages and connections to the subsystems were required.
As a principle, the MBG system operated with "single lever control", via the Throttle lever, and this gave simplification to the operation of the aircraft. In fact, if you study the Fw 190 D-9 fighter, you will see that it has only the throttle lever, no propeller control or indicators.
Junkers had gone even further than that, the Jumo 213 engines do not have a conventional throttle. They do have a direct starting and low power throttle but the main function of airflow control is by a Swirl throttle on the supercharger intake that more efficiently controls airflow in the power range of the engine. The Swirl throttle (or inlet guide vanes) are adjusted by the function of the MBG using pressure oil to the adjustment ram on the supercharger casing.
Overall, the MBG function was designed to match fuel flow and airmassflow to give a power output directly related to power output demand by the throttle lever position. This functionality is claimed by Junkers in the Handbuch to not require the MAP gauge, the main indication of power is the rpm and fuel flow rate. Junkers state that the MAP gauge is only needed as a cross-reference. However, study of the Fw 190 D and Ta 152 versions with the Jumo 213 engines shows the installation of MAP gauges but no fuel flow rate gauges!

Going back to the original question about the MBG override, we can see that the manual control of the starting Drosselklappe was needed for engine start in temperatures of 0 to minus 25 degrees C. The other use of the over-ride was for low-power engine control if the Swirl throttle control function was lost or suspected. This type of fault with the MBG is recognised in the Handbuch, where it states that malfunction or defect in the MBG is usually in the Swirl throttle control capsule and to make this repair easier, the control unit (Fullungsregler) was made easily changable.
I enclose a page from the Handbuch that shows where the Fullungsregler is fitted on the MBG, and how to change it.

Cheers

Eng

JUMO213A61.jpg
 
Hi all,

I have tried to find more original detail about the JUMO 213 MBG in detail. Unfortunately, there seems to not be much online. I have found some explanation of the system on some WW2 Simulations, but nothing really detailed. It looks like I might have to purchase the Hafner Archiv compilation to see if there is more detail.
I will attempt to post a large photo of a 213 MBG that comes from the Deutches Museum. This item is fitted at the lower rear left of the 213. The side cover has been replaced with a perspex plate, but you can't see much detail inside. The lever sticking through the perspex cover is the pilots throttle lever connection and the three pipes over the top are the hydraulic lines to the swirl throttle operating piston. The Fullungsregler referred to before above, is on the left.

Cheers

Eng

JUMO213MBGG18.png
 

Users who are viewing this thread

Back