5" 38 Mark 28 Twin Gun Secondary Battery from Iowa Class Battleships
- Thread starter Builder 2010
- Start date
Ad: This forum contains affiliate links to products on Amazon and eBay. More information in Terms and rules
Vic Balshaw
Major General
This is looking amazing. 
Great work so far!
- Thread starter
- #304
Builder 2010
Staff Sergeant
Thanks guys!
Happy Mother's Day to all for which it is appropriate!
Several things are going on. Almost done the model proper. All the major painting is done, have to finalize the electronics, and produce some more graphics. Deck to cabin attachement is nearly complete. Both the main deck to 2nd Deck Compartments, and Magazine Ceiling to Magazine are now held with screws. All linoleum is finish coated. Gun house is finally ready for joining to UHR and everthing is filled that needed to be.
However, I have a major glitch with the plexiglass. I took a small risk ordering the plexiglass by measurements given to me by my friend Bryan, the base builder.
I picked up the Plexiglass on Thursday and the base arrived in perfect condition on Friday.
When I tried the plexiglass on for size, the front/back and top were about 1 1/4" too short!!! The sides were fine. What the heck happened???
Went back to my drawings and realized that when Bryant gave me the measurements they were shorter than what I had on my drawing. A red flag should have gone up, but instead, I adjusted my drawing, and then measured the plexiglass with this new measure. That was wrong! I should have called Bryant and asked him to recheck.
I called General Rubber & Plastics here in town and asked them to cut three more piecces to the new measures as taken diectly from the (CORRECT) base and they will rush the job. If it comes in by Wednesday, I will be okay. Thrusday may not work since the acrylic cement takes 24 hours to fully cure and I don't want to risk it coming apart during handling.
So what went wrong. Bryant is a perfectionist (like I am sometimes), but it was his error. His ruler's end is not the start of the measuring and he forgot to add the difference. Ergo, he measured the correct base and got an incorrect answer. The worst that can happen is it cost me an additional $50.00.
I got most of the detail painting done on the three new Lower Hoists. They came out very nicely. Still need to pick out details.
I masked the edges and brush-painted the linoleum color on the magazine and visible floors on the 2nd deck. And with the apparatus fitted. I may not use my roof beams. They are going to impinge on the hoists. My hoists may be a tad over-sized and my beams are definitely over-sized. Regardless, they will be hard to see.
I will call General Rubber tomorrow and get a fix on delivery. Shouldn't take to long to cut 3 peices of 3/16 plexiglass. They mill it will a CNC machine so the edges are just about ready for gluing. I hit them with some light sanding, chamfer slightly the gluing edge and they're ready to go. Should only take 1/2 hour to make the case once I have the correct stock in hand.
I really want to deliver this when we're at the dry dock tour. It's a perfect time to get it there with the renewed interest in the ship with all the news coverage it's been getting. It would be great to have it sitting next to the big gun when it reopens in June. If I miss this date it will have to wait until we drive back East again, and that could be as late as fall. Meanwhile, it would sitting around here risking something bad happening to it.
Happy Mother's Day to all for which it is appropriate!
Several things are going on. Almost done the model proper. All the major painting is done, have to finalize the electronics, and produce some more graphics. Deck to cabin attachement is nearly complete. Both the main deck to 2nd Deck Compartments, and Magazine Ceiling to Magazine are now held with screws. All linoleum is finish coated. Gun house is finally ready for joining to UHR and everthing is filled that needed to be.
However, I have a major glitch with the plexiglass. I took a small risk ordering the plexiglass by measurements given to me by my friend Bryan, the base builder.
I picked up the Plexiglass on Thursday and the base arrived in perfect condition on Friday.
When I tried the plexiglass on for size, the front/back and top were about 1 1/4" too short!!! The sides were fine. What the heck happened???
Went back to my drawings and realized that when Bryant gave me the measurements they were shorter than what I had on my drawing. A red flag should have gone up, but instead, I adjusted my drawing, and then measured the plexiglass with this new measure. That was wrong! I should have called Bryant and asked him to recheck.
I called General Rubber & Plastics here in town and asked them to cut three more piecces to the new measures as taken diectly from the (CORRECT) base and they will rush the job. If it comes in by Wednesday, I will be okay. Thrusday may not work since the acrylic cement takes 24 hours to fully cure and I don't want to risk it coming apart during handling.
So what went wrong. Bryant is a perfectionist (like I am sometimes), but it was his error. His ruler's end is not the start of the measuring and he forgot to add the difference. Ergo, he measured the correct base and got an incorrect answer. The worst that can happen is it cost me an additional $50.00.
I got most of the detail painting done on the three new Lower Hoists. They came out very nicely. Still need to pick out details.
I masked the edges and brush-painted the linoleum color on the magazine and visible floors on the 2nd deck. And with the apparatus fitted. I may not use my roof beams. They are going to impinge on the hoists. My hoists may be a tad over-sized and my beams are definitely over-sized. Regardless, they will be hard to see.
I will call General Rubber tomorrow and get a fix on delivery. Shouldn't take to long to cut 3 peices of 3/16 plexiglass. They mill it will a CNC machine so the edges are just about ready for gluing. I hit them with some light sanding, chamfer slightly the gluing edge and they're ready to go. Should only take 1/2 hour to make the case once I have the correct stock in hand.
I really want to deliver this when we're at the dry dock tour. It's a perfect time to get it there with the renewed interest in the ship with all the news coverage it's been getting. It would be great to have it sitting next to the big gun when it reopens in June. If I miss this date it will have to wait until we drive back East again, and that could be as late as fall. Meanwhile, it would sitting around here risking something bad happening to it.
Looks great so far!
- Thread starter
- #307
Builder 2010
Staff Sergeant
Made substantial progress today, and I'm feeling pretty good about finishing the model (at least) on time. Finished all the detail painting on the reprinted lower hoists so they're done. Built the LED driver board with 7 parallel circuits. 6 are dedicted now, but I'm thinking of adding some light into the 2nd deck cabins showing the hoist trunks and one over the overhang where I may be placing the nameplate. If I don't put it there, it will be adhered to the back wall of the showcase.
Since I'm already paralleling some of the negative leads before they even get to the circuti board, I don't need very many barrier terminals. I DO need a separate positive circuit for each 3-LED series sub-circuit.
The bottom is not very neat because it not really a printed circuit board. It's more like a bread board. The positive ends of the CL2N3 driver chips is a common bus, but the output side goes to each circuit individually.
I finished crafting the final wall structure; the sample of the superstructure that resides next to the #4 gun mount. I needed to make precise holes to accept the 3D printed porthole assemblies. It's a pretty big hole and I attempted to grind a plastic-pointed drill with the 100º drill point angle. It didn't work and grabbed and tore my test piece. I reverted to making my "Poor-man's Punch" scheme.
It goes like this:
1. Grind the tail end of the drill you want to use with a diagonal flat surface.
2. Lightly grind the diameter to remove any burrs and give a sharp edge/
3. With the business-end of the drill, create a hole in a piece of steel, aluminum or brass that will serve as the die side.
4. Reverse the drill in the drill press with the punch-end in this newly formed hole to align it with the drill press spindle.
5. Lower the chuck while loose over the punch and manipulate it so it is as vertical as you can get it.
6. Clamp the die end (over a block of wood with the same hole) and clamp the drill press table.
7. Tighten the flute end of the drill in the chuck without disturbing the geometry. Note: the drill really isn't symetrical and clamping it in a 3-jaw drill chuck is optimal. You're not going to turn the drill on, just press straight down
8. Place the plastic on the die and punch the hole.
I laid out the hole locations and scribed circles of the correct diameter to use as a guide when positioning under the punch.
This was the test!
And here was the actual run. The plastic doesn't pull away when you raise the tool. Real punch presses have stripper plates that sit between the punch and die to remove the part from the punch. Since it's just plastic, it's not hard to remove the workpice.
Here were the pieces punched for the portholes.
And assembled.
And now with the portholes installed.
Notice there is a raised lip around the porthole which is exactly as I wanted it with the 0.040" plastic sheet I was using.
This is the back side with won't be viewed by the public, but all the porthole details are there.
Tomorrow, this new stuff gets painted. And I will start on planking the main deck. Should take a day. More painting needs to be done on some of the decks. Final assembly should be on Wednesday and hopefully building the case.
I finalize the AV program, but don't yet have the digital picture frame. You can get 15" screens for about $100.00 and I'm trying to convince Ryan to spring for this one thing.
Here's a sample of the visuals i created for AV program.
Since I'm already paralleling some of the negative leads before they even get to the circuti board, I don't need very many barrier terminals. I DO need a separate positive circuit for each 3-LED series sub-circuit.
The bottom is not very neat because it not really a printed circuit board. It's more like a bread board. The positive ends of the CL2N3 driver chips is a common bus, but the output side goes to each circuit individually.
I finished crafting the final wall structure; the sample of the superstructure that resides next to the #4 gun mount. I needed to make precise holes to accept the 3D printed porthole assemblies. It's a pretty big hole and I attempted to grind a plastic-pointed drill with the 100º drill point angle. It didn't work and grabbed and tore my test piece. I reverted to making my "Poor-man's Punch" scheme.
It goes like this:
1. Grind the tail end of the drill you want to use with a diagonal flat surface.
2. Lightly grind the diameter to remove any burrs and give a sharp edge/
3. With the business-end of the drill, create a hole in a piece of steel, aluminum or brass that will serve as the die side.
4. Reverse the drill in the drill press with the punch-end in this newly formed hole to align it with the drill press spindle.
5. Lower the chuck while loose over the punch and manipulate it so it is as vertical as you can get it.
6. Clamp the die end (over a block of wood with the same hole) and clamp the drill press table.
7. Tighten the flute end of the drill in the chuck without disturbing the geometry. Note: the drill really isn't symetrical and clamping it in a 3-jaw drill chuck is optimal. You're not going to turn the drill on, just press straight down
8. Place the plastic on the die and punch the hole.
I laid out the hole locations and scribed circles of the correct diameter to use as a guide when positioning under the punch.
This was the test!
And here was the actual run. The plastic doesn't pull away when you raise the tool. Real punch presses have stripper plates that sit between the punch and die to remove the part from the punch. Since it's just plastic, it's not hard to remove the workpice.
Here were the pieces punched for the portholes.
And assembled.
And now with the portholes installed.
Notice there is a raised lip around the porthole which is exactly as I wanted it with the 0.040" plastic sheet I was using.
This is the back side with won't be viewed by the public, but all the porthole details are there.
Tomorrow, this new stuff gets painted. And I will start on planking the main deck. Should take a day. More painting needs to be done on some of the decks. Final assembly should be on Wednesday and hopefully building the case.
I finalize the AV program, but don't yet have the digital picture frame. You can get 15" screens for about $100.00 and I'm trying to convince Ryan to spring for this one thing.
Here's a sample of the visuals i created for AV program.
Great work so far!
- Thread starter
- #310
Builder 2010
Staff Sergeant
Thanks for the input. I'm using the acrylic adhesive that they sell at the plastics house. It appears to work like other acrylic cements with very low viscosity and the ability to be attracted by static charge.
The replacements were available today. I picked them up in the early afternoon and got the case built by 4:30. I'm getting better at building these things, but I'm still not great. This one has a minimum of glue where it's not supposed to go. For that I am thankful.
Before I retrieved it, I did more detail work on the model. I installed 3/16" square stock edge thickeners on the upper superstructure to provide more glue surface when I glue it down tomorrow. I also added a corner brace to square up that external 90º corner. I then started to paint it and realized I hadn't installed the "eyebrows" over the portholes. It's a little detail, but I wanted to include it. I was using a very forgiving paint (Life Color), wiped it off and made the eyebrows out some very small styrene strip. I got them on and painted the part. To fully cure it takes overnight.
I also finally painted all the cutaway edges of the magazine and 2nd Deck compartment openings, and final touch up on the gun house and UHR. They're all ready for final assembly. I used Vallejo Crimson Red, and then back painted all the red that got on the outer surfaces with Vallejo White. Both paints have good hiding qualities and the final looks very neat and trim. I'm still worried about doing the planked deck. It could take a lot of time which I no longer have. I have two days!
Then I got the case parts. I was disappointed that the replacement parts were saw-cut and not CNC milled. They were much rougher and had some chipping. I'm not complaining. They turned the job over in less than two days. They'll suffice.
To clean up the edges some… I have a edge sanding contraption that I built when gluing up balsa skins making a very large RC aircraft 13 years ago. It's a 1X3 screwed to a 1X4 capturing the sandpaper in between. It provides a long, square edged surface with abrasive and works pretty well. The saw marks were deeper than it was reasonable to expect their removal via hand sanding.
After cleaning up the edges as good as I could get, I determined the edge that were going to get glued and created a very slight chamfer on the inside glue edge with a sanding block. The chamfer is very small, but enough to help guide the needle applicator and promote capilary flow. Speaking of capilary flow, I was also told to use a Q-tip and coat the glue edges with cement before taping together. It helps flow into the joint.
The fellow at the plastics house also recommended removing ALL the protective film. It just gets in the way. Acrylic has a lot of static charge. It's a problem because it will draw cement off the applicator and deposit it where you don't want it. Another trick he told me last time was to do all the work with the assembly sitting on a damp towel to reduce static charge.
I then used two micro-fiber cloths to clean off any dirt and sanding debris. One was damp followed by a clean dry one. These cloths are fabulous! I bought a stack of 100 of them from Amazon for something around $12.00. They're washable and worked great on the stove, cleaning leather car upholstery, mirrors, etc. And they worked great on acrylic!
I started taping it all together using Tamiya wide tape, but it didn't have enough grip strength to hold it together. I switched to 3M Blue Tape. I put the sides together first sitting on the top piece, and then errored thinking that I had to turn it over to get the top fitted. That attempt loosened a lot of the tape forcing me to reconsider. I replaced the taped-together-walls back on the top, slide it off the table a bit and so I could apply tape to its underside, rotated it off the edge and did the rest of the sides in order.
Tomorrow starts the full-court press. If I don't get it done, I can't blame the Plexiglass.
I applied the glue using the last tip I received; squeeze the air out of the bottle applicator and then release as you rotate the tip into position. This way you don't get that "spurt" when you tip the bottle oveer to apply the cement. This tip really helps making clean job.
I made a measurement error too. I made the height measure for the new long pieces 1/16" too tall. It shows up here…
The effect is to raise the ends a little off the wood base, but it's well supported by the long sides. Oh well…
After gluing, letting it set up about 1/2 hour, I was able to lift it, put it on the base and clean off any tape residue. It came out very clean and better than my past attempts.
Tomorrow I'll flame polished the exposed edges with a MAPP gas torch.
The replacements were available today. I picked them up in the early afternoon and got the case built by 4:30. I'm getting better at building these things, but I'm still not great. This one has a minimum of glue where it's not supposed to go. For that I am thankful.
Before I retrieved it, I did more detail work on the model. I installed 3/16" square stock edge thickeners on the upper superstructure to provide more glue surface when I glue it down tomorrow. I also added a corner brace to square up that external 90º corner. I then started to paint it and realized I hadn't installed the "eyebrows" over the portholes. It's a little detail, but I wanted to include it. I was using a very forgiving paint (Life Color), wiped it off and made the eyebrows out some very small styrene strip. I got them on and painted the part. To fully cure it takes overnight.
I also finally painted all the cutaway edges of the magazine and 2nd Deck compartment openings, and final touch up on the gun house and UHR. They're all ready for final assembly. I used Vallejo Crimson Red, and then back painted all the red that got on the outer surfaces with Vallejo White. Both paints have good hiding qualities and the final looks very neat and trim. I'm still worried about doing the planked deck. It could take a lot of time which I no longer have. I have two days!
Then I got the case parts. I was disappointed that the replacement parts were saw-cut and not CNC milled. They were much rougher and had some chipping. I'm not complaining. They turned the job over in less than two days. They'll suffice.
To clean up the edges some… I have a edge sanding contraption that I built when gluing up balsa skins making a very large RC aircraft 13 years ago. It's a 1X3 screwed to a 1X4 capturing the sandpaper in between. It provides a long, square edged surface with abrasive and works pretty well. The saw marks were deeper than it was reasonable to expect their removal via hand sanding.
After cleaning up the edges as good as I could get, I determined the edge that were going to get glued and created a very slight chamfer on the inside glue edge with a sanding block. The chamfer is very small, but enough to help guide the needle applicator and promote capilary flow. Speaking of capilary flow, I was also told to use a Q-tip and coat the glue edges with cement before taping together. It helps flow into the joint.
The fellow at the plastics house also recommended removing ALL the protective film. It just gets in the way. Acrylic has a lot of static charge. It's a problem because it will draw cement off the applicator and deposit it where you don't want it. Another trick he told me last time was to do all the work with the assembly sitting on a damp towel to reduce static charge.
I then used two micro-fiber cloths to clean off any dirt and sanding debris. One was damp followed by a clean dry one. These cloths are fabulous! I bought a stack of 100 of them from Amazon for something around $12.00. They're washable and worked great on the stove, cleaning leather car upholstery, mirrors, etc. And they worked great on acrylic!
I started taping it all together using Tamiya wide tape, but it didn't have enough grip strength to hold it together. I switched to 3M Blue Tape. I put the sides together first sitting on the top piece, and then errored thinking that I had to turn it over to get the top fitted. That attempt loosened a lot of the tape forcing me to reconsider. I replaced the taped-together-walls back on the top, slide it off the table a bit and so I could apply tape to its underside, rotated it off the edge and did the rest of the sides in order.
Tomorrow starts the full-court press. If I don't get it done, I can't blame the Plexiglass.
I applied the glue using the last tip I received; squeeze the air out of the bottle applicator and then release as you rotate the tip into position. This way you don't get that "spurt" when you tip the bottle oveer to apply the cement. This tip really helps making clean job.
I made a measurement error too. I made the height measure for the new long pieces 1/16" too tall. It shows up here…
The effect is to raise the ends a little off the wood base, but it's well supported by the long sides. Oh well…
After gluing, letting it set up about 1/2 hour, I was able to lift it, put it on the base and clean off any tape residue. It came out very clean and better than my past attempts.
Tomorrow I'll flame polished the exposed edges with a MAPP gas torch.
Vic Balshaw
Major General
Almost done.
- Thread starter
- #313
Builder 2010
Staff Sergeant
The end is nigh! I got the main deck planked in a little over two hours. I woke worried that I didn't have enough scale wood, but I had way more than I needed. I gang cut the wood in my modified Chopper 2. I built a depth stop on this useful tool, that lacked it. I makes it much more useful. I cut the scale 3 X 2s to scale 8' lengths. I don't really know how long the deck planks are, but they don't look very long.
I laid the 16" long strips on the deck to estimate how many planks I would need.
In the past when I planked a deck that had dark caulking, I laid strips of black construction paper edge-on, and then shaved the excess off with a razor. I didn't have the paper so I tried another approach. I mixed Aleen's Tacky Glue with black India Ink to make a jet black PVA glue. I pre-stained the planks, but after sanding most of the color was removed. The black glue make the joints dark and looks pretty good.
When first applied it looked like a mess.
And when fully planked really didn't impress me very much.
But, after sanding, it looked pretty good. I started by brushing the glue onto each piece before placing it. This is what made most of the mess. About halfway through switched to brushing the glue on to the substrate. Not only was it much cleaner, but it went at least twice as fast.
And with a coat of clear Urethane, it looks pretty nice indeed. Tomorrow I'll glue down the superstructure. It's just sitting there now. I can't forget I have to make window glazing.
I laid out and drilled for the railings. The end stanchions have faux turnbuckles. They look good, but are very, very fragile. I'm going to rig with E-Z Line and will wait until I'm ready to put the case on before doing it so I won't be reaching over it to do anything else.
I got the power system all button up and made a brass plate to hold the power switch. I'm not turning on the primary. Instead, I'm turning off the secondary. Everything is waiting for the wiring to come down from the model.
So… what's left. Everything is painted and staged. I have to asssemble the layers together. Before doing that I have to populate the magazine with all of it's appliances. I have to paint one exposed deck, that's now white, but I want it linoleum color. I have to install the chunks of the hoist trunks during the stacking process. Lastly, I have to make the locking system for the showcase like i did with the big gun.
Meanwhile, we're going to early vote tomorrow since we'll be gone on primary day and I have a cardiology checkup at 1:00. Still, I'm optimitic that I can bring it all together. I was worried about the case and the planking and both are done and no longer an issue. The rest should go together pretty well. (Famous last words!).
I laid the 16" long strips on the deck to estimate how many planks I would need.
In the past when I planked a deck that had dark caulking, I laid strips of black construction paper edge-on, and then shaved the excess off with a razor. I didn't have the paper so I tried another approach. I mixed Aleen's Tacky Glue with black India Ink to make a jet black PVA glue. I pre-stained the planks, but after sanding most of the color was removed. The black glue make the joints dark and looks pretty good.
When first applied it looked like a mess.
And when fully planked really didn't impress me very much.
But, after sanding, it looked pretty good. I started by brushing the glue onto each piece before placing it. This is what made most of the mess. About halfway through switched to brushing the glue on to the substrate. Not only was it much cleaner, but it went at least twice as fast.
And with a coat of clear Urethane, it looks pretty nice indeed. Tomorrow I'll glue down the superstructure. It's just sitting there now. I can't forget I have to make window glazing.
I laid out and drilled for the railings. The end stanchions have faux turnbuckles. They look good, but are very, very fragile. I'm going to rig with E-Z Line and will wait until I'm ready to put the case on before doing it so I won't be reaching over it to do anything else.
I got the power system all button up and made a brass plate to hold the power switch. I'm not turning on the primary. Instead, I'm turning off the secondary. Everything is waiting for the wiring to come down from the model.
So… what's left. Everything is painted and staged. I have to asssemble the layers together. Before doing that I have to populate the magazine with all of it's appliances. I have to paint one exposed deck, that's now white, but I want it linoleum color. I have to install the chunks of the hoist trunks during the stacking process. Lastly, I have to make the locking system for the showcase like i did with the big gun.
Meanwhile, we're going to early vote tomorrow since we'll be gone on primary day and I have a cardiology checkup at 1:00. Still, I'm optimitic that I can bring it all together. I was worried about the case and the planking and both are done and no longer an issue. The rest should go together pretty well. (Famous last words!).
Vic Balshaw
Major General
It's all looking good and good luck with the cardiology tomorrow, I have my annual check due in just under a month.
BertUS
Senior Airman
Looks great and like Vic said, Good luck with your check
Excellent work so far!
Airframes
Benevolens Magister
Beautiful work, and good luck with the check-up.
- Thread starter
- #319
Builder 2010
Staff Sergeant
Thanks Fellas! My checkup went well. I've been in permanent AFib for about 7 years. You can live well with it as long as you take you beta blocker and blood thinners. I also manage my pressure and cholesterol so he says I'm doing all the right things to keep going.
My optismism was not well-placed. I came very close to finishing today, but, as usual, something in the final assembly proved much more challenging that it would have appeared. That said, I did get much done. I got the magazine finished, mounted on the base and fastened it's roof on with the wiring led below. I got the splinter deck glued to this roof and then actually glued the second deck in place. I got the gun house and UHR joined and decided on the simplest of conduits for the rest of the wiring. But what got me was trying to install those segregated pieces of hoist trunk through the cutaway openings in the 2nd deck cabins. It was very difficult… it was getting messy… I was running out of time and I envisioned bad things happening. I gave up and will pick it up after we return. Besides, Ryan has his hands full right now and it might not have been such a good tie to bring it.
I you look closely at this image, you might pick up that I installed that first row of powder canisters backwards. I know it's backwards because I spent a lot of time painting the yellow on the openning end of the canister and they're not seen here. Would anyone care? No! But, it's an indication that I was rushing. Things don't go well when I do.
I got the little steps laind in at the base of the powder room doors and painted the mechanism steel color. I used 3M transfer tape to hold the hoists down. All the rest is held by the J-B Weld construction adhesive.
I pre-fit the stack with a couple of small screws holding the magazine ceiling and reckoned where the UHR wiring was going to penetrate the main deck. I marked this and drilled all the way through the stack with a 1/4" plastic drill bit. I then used a transfer punch to mark the location of this hole on the base. For the uninitiated, a transfer punch is a specifically-sized piece of tool steel with a center-punch point on it. They come in a set that matches a full set of drills and they're used to mark locations using a hole as the datum. (harder to describe than used).
I drilled the base with the 1/4" brad point drill and now had a straight path for the wiring to go below through a brass 1/4" tube. The tube will be visible, but not obtrusive and will help support that very cantilvered from of the model. It also greatly simplified getting the wring done.
Here's the punch before running it all the way down and tapping lightly with a jeweler's hammer.
The conduit top opening fits directly under the openning in the UHR 's rear floor next to the back support.
Here's the lead opening in the UHR floor.
I'm going to chemically treat the brass tube so it will be very dark and in the background.
My arrangement varies slightly from my original design bringing the splinter deck and cabin all the wasy forward. This changed the trajectory of the hoist trunks.
I used the plans to find the location of the Splinter Deck lattice and then to remove any interfering lattice so the hoist trunks can pass through. If you remember, I originally drew and printed openings. This all went out the window since I had slightly changed the geometry.
I made small drill marks at the corners of the rectangles that represent the hoist trunks at that posiition. After gluing down the lattic and the hoist trunk parts, they didn't align well with the hoists themseleve and I had to position them back and to the left about a 1/4". I then removed any interfering lattice.
After assemblng and gluing the whole stack, In my agression fitting the rest of the hoist trunks the glue fell apart, but it was good it did. I was having trouble getting the middle to settle in properly. The reason was the hoist parts were about 3/32" too high and well keeping the whole center from gluing.
I broke them loose (they were CA'd) and ground off the excess on the belt sander. So when I finally glue it back together it should nestle down much better.
I glued a thin strip of styrene on the front deck edge as a scupper gutter. Needs to be painted.
This was the clamping scheme.
I finally put the gun house and UHR together with four small screws. I dont like the roof fit, but it was a 3D Printed affair and not a styrene part. I also don't like that the UHR hoists are tipped forward and not centered in the space. Can't be fixed now. That ship has left the dock.
As much as I wanted to finish it for this trip, we'll be making other trips and, as I noted, messing with the hoist pieces was getting messier after each attempt and leading to something bad to happen.
So what's left? I have to get the hoist trunks in and clean up the mess inside those spaces. I have to connect the field wiring. The railing needs to be built as the last thing. I have to mount the name plate and the one graphic on the rear case wall, and make the lock clamps for same. Instead of the construction glue, I'm going to use the J-B Epoxy designed for plastics. It needs to be secure. I screws the magazine to base with self-tapping screws so it's not going anywhere.
Everyone have a nice Memorial Day and I'll be back after that.
My optismism was not well-placed. I came very close to finishing today, but, as usual, something in the final assembly proved much more challenging that it would have appeared. That said, I did get much done. I got the magazine finished, mounted on the base and fastened it's roof on with the wiring led below. I got the splinter deck glued to this roof and then actually glued the second deck in place. I got the gun house and UHR joined and decided on the simplest of conduits for the rest of the wiring. But what got me was trying to install those segregated pieces of hoist trunk through the cutaway openings in the 2nd deck cabins. It was very difficult… it was getting messy… I was running out of time and I envisioned bad things happening. I gave up and will pick it up after we return. Besides, Ryan has his hands full right now and it might not have been such a good tie to bring it.
I you look closely at this image, you might pick up that I installed that first row of powder canisters backwards. I know it's backwards because I spent a lot of time painting the yellow on the openning end of the canister and they're not seen here. Would anyone care? No! But, it's an indication that I was rushing. Things don't go well when I do.
I got the little steps laind in at the base of the powder room doors and painted the mechanism steel color. I used 3M transfer tape to hold the hoists down. All the rest is held by the J-B Weld construction adhesive.
I pre-fit the stack with a couple of small screws holding the magazine ceiling and reckoned where the UHR wiring was going to penetrate the main deck. I marked this and drilled all the way through the stack with a 1/4" plastic drill bit. I then used a transfer punch to mark the location of this hole on the base. For the uninitiated, a transfer punch is a specifically-sized piece of tool steel with a center-punch point on it. They come in a set that matches a full set of drills and they're used to mark locations using a hole as the datum. (harder to describe than used).
I drilled the base with the 1/4" brad point drill and now had a straight path for the wiring to go below through a brass 1/4" tube. The tube will be visible, but not obtrusive and will help support that very cantilvered from of the model. It also greatly simplified getting the wring done.
Here's the punch before running it all the way down and tapping lightly with a jeweler's hammer.
The conduit top opening fits directly under the openning in the UHR 's rear floor next to the back support.
Here's the lead opening in the UHR floor.
I'm going to chemically treat the brass tube so it will be very dark and in the background.
My arrangement varies slightly from my original design bringing the splinter deck and cabin all the wasy forward. This changed the trajectory of the hoist trunks.
I used the plans to find the location of the Splinter Deck lattice and then to remove any interfering lattice so the hoist trunks can pass through. If you remember, I originally drew and printed openings. This all went out the window since I had slightly changed the geometry.
I made small drill marks at the corners of the rectangles that represent the hoist trunks at that posiition. After gluing down the lattic and the hoist trunk parts, they didn't align well with the hoists themseleve and I had to position them back and to the left about a 1/4". I then removed any interfering lattice.
After assemblng and gluing the whole stack, In my agression fitting the rest of the hoist trunks the glue fell apart, but it was good it did. I was having trouble getting the middle to settle in properly. The reason was the hoist parts were about 3/32" too high and well keeping the whole center from gluing.
I broke them loose (they were CA'd) and ground off the excess on the belt sander. So when I finally glue it back together it should nestle down much better.
I glued a thin strip of styrene on the front deck edge as a scupper gutter. Needs to be painted.
This was the clamping scheme.
I finally put the gun house and UHR together with four small screws. I dont like the roof fit, but it was a 3D Printed affair and not a styrene part. I also don't like that the UHR hoists are tipped forward and not centered in the space. Can't be fixed now. That ship has left the dock.
As much as I wanted to finish it for this trip, we'll be making other trips and, as I noted, messing with the hoist pieces was getting messier after each attempt and leading to something bad to happen.
So what's left? I have to get the hoist trunks in and clean up the mess inside those spaces. I have to connect the field wiring. The railing needs to be built as the last thing. I have to mount the name plate and the one graphic on the rear case wall, and make the lock clamps for same. Instead of the construction glue, I'm going to use the J-B Epoxy designed for plastics. It needs to be secure. I screws the magazine to base with self-tapping screws so it's not going anywhere.
Everyone have a nice Memorial Day and I'll be back after that.
SaparotRob
Unter Gemeine Geschwader Murmeltier XIII
Incredibly well done, Sir.
