fubar57
General
Good stuff. Flashbacks but once you know the problem areas it doesn't take anything away from the build
GB-63 1/48 Hawker Typhoon 1B - Stormy Weather
- Thread starter Crimea_River
- Start date
Ad: This forum contains affiliate links to products on Amazon and eBay. More information in Terms and rules
Vic Balshaw
Major General
Coming along nicely Andy. 
Looks good so far Andy!
Lots of fun stuff to come....
Jock Tamson
Staff Sergeant
Coming together nicely 
- Thread starter
- #46
Crimea_River
Marshal
Thanks all
Still doing some filling and sanding on the fuselage seams. In the meantime, I opened the ejection ports on the wing and began drilling out the landing lights. Both lights were present on this particular Typhoon whereas many had one faired over.
Still doing some filling and sanding on the fuselage seams. In the meantime, I opened the ejection ports on the wing and began drilling out the landing lights. Both lights were present on this particular Typhoon whereas many had one faired over.
fubar57
General
Nice grinding
Vic Balshaw
Major General
Good detailing.
- Thread starter
- #50
Crimea_River
Marshal
Thanks all.
Continuing with fuselage seam treatment but a question for y'all. 90% sure of the answer but want to check anyway.
This little nubbin that I've been carefully sanding around is for a light that was present on "early" Typhoons. However, I'm not sure if/when it was deleted. Would it have been gone by the time the JRxxx series was built? I reckon so.
Continuing with fuselage seam treatment but a question for y'all. 90% sure of the answer but want to check anyway.
This little nubbin that I've been carefully sanding around is for a light that was present on "early" Typhoons. However, I'm not sure if/when it was deleted. Would it have been gone by the time the JRxxx series was built? I reckon so.
fubar57
General
Is this the light Andy? MN658
Yes Geo that's the top white nav light. However there is no rule IMHO. I have seen the JP, RB, SW and MN series Typhoons without the light noticed. It wasn't too small item that could be unnoticed in the pics ...
the pic source: the net.
the pic source: the net.
Nice work so far Andy!
- Thread starter
- #54
Crimea_River
Marshal
Thanks guys. I think I will leave the light off. I believe the first two pics Wojtek posted are prototype bubble tops.
Last edited:
- Thread starter
- #55
Crimea_River
Marshal
I had to take a break after an hour this morning as my hands were getting too shaky! I'm close to applying a trial primer coat to the fuselage to test my seam work and, as always, I try to think ahead to all the parts that need a primer since Tamiya's grey surface primer is lacquer based and I want to minimize how many times I run this crap through my airbrush because of the fumes. So, I decided to tackle the bombs which are made up of resin and PE parts, both of which need a good lacquer based primer.
VERY finicky! I started with removing the body from the rather large casting block, which was no problem. Next came flattening the nose a little and adding the tiny nose pistol vanes. Shaking starts as the cuts need to be perfectly flat and perpendicular so the part needs to be held firmly (but not too firmly - PING!) in tweezers and filed carefully. Next came the PE fins which weren't too much of an issue, other than getting the cruciform angles perfect. Then came the very thin resin cylindrical vane, which just begged to be broken during removal from the casting block and clean-up. I managed to not break it but fitting it over the fins took some doing, shake, shake. The tiny PE arming vane on the back was next and this went OK.
Then came the extremely thin stabilizers. Cleaning these delicate parts induced more shaking but I managed to hold it together. I debated the options of either gluing these to the hard point fairings or to the bombs. I chose the latter since I want to glue the fairings to the wings and paint them along with the undersides. Having these delicate stabilizers glued to the fairings would have no doubt resulted in damage so I opted to attach them to the bombs which will make fitting the bombs to the model later much easier. However, this required accurate placement of the tiny parts onto the bomb so that the stabilizers would fit properly into the slots in the fairing. I used my dial vernier to measure the spacing, then made pencil marks on the bomb that straddled the suspension lug equally and glued them in place. This took several tries but I finally got them on.
At this point I decided not to push my luck and tackle the second bomb. Here are pics of one finished bomb along with the pieces for the second one, which will be done after I take a sedative.
Thanks for looking in guys.
VERY finicky! I started with removing the body from the rather large casting block, which was no problem. Next came flattening the nose a little and adding the tiny nose pistol vanes. Shaking starts as the cuts need to be perfectly flat and perpendicular so the part needs to be held firmly (but not too firmly - PING!) in tweezers and filed carefully. Next came the PE fins which weren't too much of an issue, other than getting the cruciform angles perfect. Then came the very thin resin cylindrical vane, which just begged to be broken during removal from the casting block and clean-up. I managed to not break it but fitting it over the fins took some doing, shake, shake. The tiny PE arming vane on the back was next and this went OK.
Then came the extremely thin stabilizers. Cleaning these delicate parts induced more shaking but I managed to hold it together. I debated the options of either gluing these to the hard point fairings or to the bombs. I chose the latter since I want to glue the fairings to the wings and paint them along with the undersides. Having these delicate stabilizers glued to the fairings would have no doubt resulted in damage so I opted to attach them to the bombs which will make fitting the bombs to the model later much easier. However, this required accurate placement of the tiny parts onto the bomb so that the stabilizers would fit properly into the slots in the fairing. I used my dial vernier to measure the spacing, then made pencil marks on the bomb that straddled the suspension lug equally and glued them in place. This took several tries but I finally got them on.
At this point I decided not to push my luck and tackle the second bomb. Here are pics of one finished bomb along with the pieces for the second one, which will be done after I take a sedative.
Thanks for looking in guys.
Vic Balshaw
Major General
You have put those little fellows together nicely.
Airframes
Benevolens Magister
Just checked a couple of references Andy, and can confirm that the I.D. lamp was not installed on production aircraft, so you're right to remove it.
fubar57
General
Luv dat bomb
- Thread starter
- #60
Crimea_River
Marshal
How about 2 then?
Finished the second one with a lot less shaking.
Now onto placing the racks.
