fubar57
General
Good stuff Bill
1/72 Super Connie HARS Livery
- Thread starter N4521U
- Start date
Ad: This forum contains affiliate links to products on Amazon and eBay. More information in Terms and rules
Nicely done so far!
- Thread starter
- #103
N4521U
Colonel
Thanks guys.
Wing is back together.
Some fine tuning for Fisher flaps.
Wing is a bit beat up as I decided to do an in flight landing config and wing was all glued up. Doh!
Doing some wheel well detail as doors will be open.
Took a long while, hours of searching for well detail shots but finally found some eggsellent ones.
The work goes on.
Wing is back together.
Some fine tuning for Fisher flaps.
Wing is a bit beat up as I decided to do an in flight landing config and wing was all glued up. Doh!
Doing some wheel well detail as doors will be open.
Took a long while, hours of searching for well detail shots but finally found some eggsellent ones.
The work goes on.
Crimea_River
Marshal
This one will look great when done judging by the work so far.
- Thread starter
- #105
N4521U
Colonel
Hoping I can pull it off.
Went back and looked at an interview of Rodney Williams, a modeler from the S.F. area who coached at monthly meetings in San Jose CA. He was doing scratch detailing before resin!!!!!! I just keep thinking, "now what would Rod do"? and try to get close. But then Sparrows who emulate Peacocks are liable to break a thigh! I digress.
Went back and looked at an interview of Rodney Williams, a modeler from the S.F. area who coached at monthly meetings in San Jose CA. He was doing scratch detailing before resin!!!!!! I just keep thinking, "now what would Rod do"? and try to get close. But then Sparrows who emulate Peacocks are liable to break a thigh! I digress.
SANCER
Senior Master Sergeant
You are doing it very well!
She is a beautiful monster!
She is a beautiful monster!
- Thread starter
- #107
N4521U
Colonel
She is a monster, of a kit!!!!!!!!!
Takes a lot to make this one work.......
Wheel wells............. Perhaps too farrrrrrrr?
Takes a lot to make this one work.......
Wheel wells............. Perhaps too farrrrrrrr?
Airframes
Benevolens Magister
Nice detail work Bill.
Crimea_River
Marshal
Looks good.
fubar57
General
Nice work Bill
Looking good so far!
- Thread starter
- #113
N4521U
Colonel
Thanks guys, I think I been away from GB39 long enough.
This is about the only detailing op I have on the Connie, and the bitts on the outside.
So I am calling the wells, Done!!!!!!
This is about the only detailing op I have on the Connie, and the bitts on the outside.
So I am calling the wells, Done!!!!!!
- Thread starter
- #115
N4521U
Colonel
Thanks. Just tryin to do a better job of scratch.
SANCER
Senior Master Sergeant
Those wells are nicely done. Good job so far Bill.
Saludos
Saludos
Lovely work so far!
ArmouredSprue
Senior Airman
It's looking really nice
- Thread starter
- #119
N4521U
Colonel
Wow, only Three years for this one!!!!!
Back onnit picking away.
Just doing some finish filling the fuselage windows
and the tail fairing missing on the kit. A little primer
to confirm it's finally smoothing. The kit is a Civilian
version, HARS is Military, different windows!
Working on decal art, Red Roo decals include windows in stripe along fuselage
So stripe will have to be painted and windows will be blade decals.
Back onnit picking away.
Just doing some finish filling the fuselage windows
and the tail fairing missing on the kit. A little primer
to confirm it's finally smoothing. The kit is a Civilian
version, HARS is Military, different windows!
Working on decal art, Red Roo decals include windows in stripe along fuselage
So stripe will have to be painted and windows will be blade decals.
