Dirk's 1/72 Frankin Defiant

Ad: This forum contains affiliate links to products on Amazon and eBay. More information in Terms and rules

dirkpitt289

Master Sergeant
2,286
20
Jul 16, 2009
South Plainfield New Jersey
This is my first attempt at this and I have no clue how its going to turn out but I gotta give it a try. No resin parts here. I'm going to do it old school and graft the nose from another kit. In this case a Spitfire Vb.

Airfix The Kit



As you all know this kit is pretty old and this one shows it. There isn't a lot of flash but the details such as the rudder have softened and lost some detail. There is also some warping of the parts.



The Donor kit



The parts I will be using from the Spitfire will be the three pieces make up the nose



As you know there is no cockpit but I want to make this in flight with the aerials deployed so I will have to scratch something together.

 


Pre-op



Post-op



While the patient was still on the table we made a few cuts to the back end as well.



Here's a comparison of the two nose sections

Profile


Nose on (Scuse the pun)



Seeing how the remaining pieces fit together



I will need to do a little more work before i will be able to get the new nose to fit. For starters I will need to thin down the fuselage.

Before



After





Thanks for looking
 
A year or so ago I saw a profile of a Defiant in Clave's Fantasy Aircraft Full Series thread. It was done in Rebel Alliance colors and had R2D2 instead of a turret. I've had doing that in the back of my head ever since. I'll have to pick up the Airfix kit one of these days and get started on it. Should be fairly simple.
 
Good stuff Dirk. Didn't the article I sent suggest using a Hurricane nose? I can't remember, but it's probably nearer in shape than the Spit.
 
I would think the Hurricane nose might be better, or alter the kit nose. The Spit front had a 'flatter' top and sides, and more 'bulbous' lower cowling. I'd have to dig out the article again, but I think it mentions extending the kit nose, and altering the intake. Might be a good idea to check the article before proceeding.
Incidentally, the 12 models covered in the book were made for display in the RAF Museum and, for the time, were probably as accurate as one could get, with materials available then.
 
Dirk is wanting to build an accurate Defiant, as far as I know. The Airfix kit was originally issued in the late 1950s or early 1960s, when access to the only complete Defiant (currently being re-restored, was in the RAF Museum) was not possible, and the kit, although passable for the time, is woefully in-accurate.
Dirk, apologies - I've just read the article I sent you, and a Spitfire MkV nose was adapted.
 
The only major kit-bash I've attempted to date is my CF-5A and it stares at me every time I go to the work bench. It seems to be saying in a fly-like voice "finish me, finish me!!!"
 
Moving forward with the Defiant we all know she has no interior whatsoever. In my opinion going crazy without some sort of vac-form canopy would be silly but then again I've been known to be quite silly at times. I will do my best to keep such interior details at a minimum. Here is where I am.

I cheated a bit with the interior. I started by painting the interior walls RAF Interior green. Instead of scratching the bits I stole them from a Me109 parts kit. What I used was the instrument panel, the pilot seat and the cockpit floor.



The pilot



The pilot finished with a wash. In order to get him to fit into the cockpit I had to spread his legs a bit. That's why he looks a little goofy



Here's how it looks. Note the IP has not been installed yet. I'm having a hard time mounting it but I think I found a solution. I scratched a bulkhead wall behind the pilots seat. The issue with that is now the uber thick canopy wont fit. If I was to shave down the bulkhead to fit the canopy it will look REALLY silly. I'm going to table that issue for the time being.



Here you can see where more surgery took place. I removed the radio and the shelf behind the pilot. I am planning on making this in flight so I want to lower the rear part of the fuselage. Here are some photos of the area.





Here is where we are. After looking at the photos I need to widen the area a little more

 
The time has come to attach the Spitfire nose.



Here is the new Spitfire Vb nose. The lips on the new nose will need to be trimmed down to get a proper fit due to the differences in the shape of the nose and the fuselage







This gaping hole will be filled with two part putty



Two part Putty for filling the holes





It appears I forgot to take a photo of the after shot. Oh well as the putty was drying I moved on to the wings. Note the poor fit





New rear shelf and radio installed



Installed the rear fuselage. Its hard to see in these photos but according to the photos of this area the piece does not drop down flush. It hinges down from the farthest point near the tail of the aircraft and lies slightly below the main fuselage. So at the black arrow its flush, at the blue arrow its slightly lower forming a lip.





Thanks for looking
 
You must log in or register to reply here.

Users who are viewing this thread

Total: 1 (members: 0, guests: 1)

Similar threads

D
1:72 Revell PT-13
Replies
7
Views
778
Lucky13
R
Arma Hobby 1/72 P-51C
Replies
8
Views
763
Ruud
Tamiya 1/72 F4U-1D RNZAF
2 3 4
Replies
78
Views
4K
Lucky13
Academy 1/72 B-17E “Pacific Theater”
Replies
9
Views
1K
Vic Balshaw
T
1/72 A&A Models Northrop F-15 Reporter (aka photo-recon P-61 Black Widow)
2
Replies
39
Views
588
Wurger
Menu
Log in
Register