**** DONE: GB-67 1/48 P-38G - Twin Engine in WWII (2 Viewers)

[Wurger]

 

[Donivanp]

Spent the night installing the gunsight/armor plate . Glued the rear window on and upper window hatch . Next to mask the clear parts and opening. Then i can spray the window frames .

View attachment 854091IMG_7751 by b007scott, on Flickr

View attachment 854092IMG_7752 by b007scott, on Flickr

View attachment 854093IMG_7753 by b007scott, on Flickr


Brian

Nicely done Brian

 

[Gnomey]

Nicely done so far!

 

[F-104nut]

Spent a couple of days got the canopy masked off . Used some Omask to mask off the open area off. Had to repaint part part of the prop hub the went around the blades that was olive drad instead of red . Got the rest of the various parts cleaned up and ready for paint. Now to spray the the window frames with interior green. Once done ill mask the wheel wells off and spray the neutral gray .

IMG_7781 by b007scott, on Flickr

149204BD-8F47-45D2-826C-38129807BB21 by b007scott, on Flickr

IMG_7818 by b007scott, on Flickr

IMG_7816 by b007scott, on Flickr


Brian

 

[Wurger]

 

[Donivanp]

Kicking it Brian.

 

[N4521U]

Ready for color, noice!

 

[Vic Balshaw]

The essential but sometimes annoying fiddly bits.

 

[F-104nut]

The essential but sometimes annoying fiddly bits.

Vic

 

[Wayne Little]

Yeah....I'm at that stage now.....too

 

[fubar57]

Beauty. Fiddly bits means close to the end

 

[F-104nut]

Started spraying the bottom side with Tamiya Neutral Gray tonight . Going to spray the demarcation the same way i did befor or try something new with blue tack .

IMG_7843 by b007scott, on Flickr


Brian

 

[fubar57]

Nice. I haven't had much success with blu-tac but slowly trying to make it work

 

[F-104nut]

Nice. I haven't had much success with blu-tac but slowly trying to make it work

I did some research and it was a feathered edge so I'll freehand airbrush it !

 

[F-104nut]

Started masking the underside today. I used the Tamiya paint guide. I cut them out in sectionsd and traced then on Tamiya tape with a pen. Used blade to cut them out. Now to mask off areas to prevent over spray .

DC9CE07D-2D84-4CB7-A8C6-7DE3B52A3898 by b007scott, on Flickr

IMG_7871 by b007scott, on Flickr

IMG_7872 by b007scott, on Flickr

IMG_7873 by b007scott, on Flickr

IMG_7875 by b007scott, on Flickr

IMG_7876 by b007scott, on Flickr

IMG_7877 by b007scott, on Flickr


Brian

 

[fubar57]

Neato

 

[Wurger]

 

[Vic Balshaw]

Super. Always think this is a hard and sometimes messy part.

 

[Donivanp]

Started masking the underside today. I used the Tamiya paint guide. I cut them out in sectionsd and traced then on Tamiya tape with a pen. Used blade to cut them out. Now to mask off areas to prevent over spray .

View attachment 855346DC9CE07D-2D84-4CB7-A8C6-7DE3B52A3898 by b007scott, on Flickr

View attachment 855347IMG_7871 by b007scott, on Flickr

View attachment 855348IMG_7872 by b007scott, on Flickr

View attachment 855349IMG_7873 by b007scott, on Flickr

View attachment 855350IMG_7875 by b007scott, on Flickr

View attachment 855351IMG_7876 by b007scott, on Flickr

View attachment 855352IMG_7877 by b007scott, on Flickr


Brian

Nice Brian, never noticed that they supplied cutouts in the kit before.

 

[A4K]

Nice Brian. Were the plans already to scale, or did you have to photocopy and enlarge them?