**** DONE: GB-68 1/48 Fw-190A-8 - We all build Fw 190 (1 Viewer)

The bulk of the decals are now on. Just a few more stencils to do, some of which I'm leaving off.

260103002.jpg
260103003.jpg
260103004.jpg


The white Gruppe bar decal is a bit transparent but I'll live with it. Chalk it up to thinned white paint. Here is the prop and spinner, awaiting a matte coat. The prop was stippled with a varying greens to represent some wear and dings.

260103001.jpg


Next up will be a panel wash, matte coat, and then more weathering. Thanks again for watching.
 
agreed, looks great Andy

I think you nailed the blue
 
Thanks again guys.

While weathering the underside, I had a mishap. I was using a small brush to paint the inside of the shell ejector chutes and accidentally dropped the brush. My attempt to remove the paint worked too well and I ended up removing all the coats down to the plastic.

260103103.jpg


No big deal. Just sanded smooth, resprayed the 76, glossed, and weathered the area again with panel line wash and mud splatters.

260103104.jpg
260103105.jpg


The undercarriage covers got the mud splatter treatment as well. Tamiya XF-52 Flat Earth dry-brush stippling.

260103101.jpg


The topsides got a bit of a panel wash as well but not so noticeable, given the dark colours. I also glued on the prop and spinner.

26020102.jpg
26020103.jpg


A closeup of the Balkenkreuz and "Nicht Anfassen" stensil on the trim tab. The decals behaved very well.

26020101.jpg


I might do a bit more schmutzing on the uppers before applying a matte coat and will report back when there's something new. Thanks again for tagging along.
 
Good recovery......aaaaahahahahaha, I kill me
 
great repair, it's coming together very nicely
 
Thanks gents. Much to report today with the main undercarriage installed, the ETC501 rack completed, and a matte coat applied.

First, the rack. The Eduard bits were supplemented with some stretched sprue sway braces (hard to see), 2 fuel lines, and a strap winch cable which are .4mm lead wire. It will be tricky threading the wires into holes that I drilled in the drop tank but it will be done. But, before adding the drop tank, I want to spray on a bit more exhaust staining.

26020201.jpg


The undercarriage legs were glued in one at a time as the connection points are a bit loosey. I wanted to be sure I got one side correct before tackling the other so, after gluing the pieces in with Tamiya Extra Thin, which has a long cure but good tack, I made any needed adjustments and then locked everything in with gel CA and accelerator. The same was then done on the other side and the alignment checked before locking in with CA.

26020204.jpg


The kit tires had been painted earlier and mudded up. I will file some flat spots on these and then glue them in place for the next update.

Here are two shots of the uppers. I used Tamiya Flat Clear for this but I need to find a better product as this leaves a noticeable dusty surface, I did not get a picture of that but I "polished" the surface a bit with a couple Q-Tips that brought out a nice sheen and got rid of the dusty appearance.

26020202.jpg
26020203.jpg


The next steps will be to do a small amount of chipping and adding the fiddly bits - antennas and wire, the pilot's step, MG and cannon barrels, and pitot tube. Thanks for your continued interest and comments.
 
Better with every post, Andy. I've been using Winsor & Newton now for my finished coats, both matte and satin. I like it a lot and super cheap. Sprayed this a day or so ago

1770076709485.png
 
Thanks guys and thanks for the tip Geo.
 

Users who are viewing this thread

Back