I am reading back through the early messages of this thread. We are having difficulties defining lightweight fighters.
From the mid-thirties to the end of WWII, the engines increased in displacement and power, and the guns got bigger and more numerous. Aircraft like the Mitsubishi A5M and the Curtis P36, developed in the thirties, used the biggest available engines, and if not (relatively) massive firepower, their armament was at least conventional. However light they were later in the war, they were conventional back in their day.
It's 1943, and the Billy Bob and Cousin Elmo aircraft company sets to work developing a lightweight fighter. In 1943, BBCE can design around the Pratt & Whitney R1830 in preference to the now available and reliable R2800. I think that less than four M2 0.5" machine guns is not a good idea. To keep the aircraft as tiny as possible, we give up high altitude performance, and range. If the aircraft is really tiny, it will have good acceleration and climb.
Returning to this premise.
Billy Bob and Cousin Elmo have bit of problem in 1943, it is sort of slump year in R-1830 development so BB and CE are faced with the choice of two 1941 R-1830 engines or building prototypes and hoping the 1944/45 R-1830s show up a bit early. I am ruling out the trubo R-1830s to keep things simple (no light-weight P-43s) but add them in if you wish.
You have the two speed R-1830 of 1200hp at sea level which sounds OK, and it's 1495lb weight. Problem is that has 1050hp at 13,100ft and that is about as good as it gets without major supercharger work AND improved cooling (new fins or aluminum cooling muff on the 1944 engines).
You have the two stage R-1830 with 1200hp at sea level and 1000hp at 19,000ft in high gear at 1560lbs plus the intercooler installation. It does not keep the plane as tiny as possible.
The already mentioned Swedish J 22 is a very good model as to what is possible, also shows a few of the problems.
6250lbs is light? Quite possibly. BB & CE may have the option to use normal Aluminum construction and either save weight to increase strength? or bit of both? 6 G loading would not be acceptable to the US. J 22 also used the retract into fuselage landing gear with narrow track, acceptable to the US gov or needs wider track and more weight?
Better fuel only helps somewhat. When the R-1830s got better fuel they rarely increase the power, what they did was increase the height at which a given power level could be used. Like 1200hp could be used at 4900ft instead of 3700ft. There may have been a cooling problem?
That is with existing historical engines. There were some 1350hp R-1830s that showed up in 1944-45 but they used new cylinders with aluminum cooling muffs, a slightly modified supercharger and plain bearings that allowed for 2800rpm instead of 2700rpm. How much of an improvement they had at high altitude is subject to question. The 1350hp was limited to 3000ft at 2800rpm while the older engines could make 1200hp 4900ft. the new engine would be down to about 1300hp at 5000ft. The American radials never got WEP unless (R-2800s) they got water injection. Perhaps a better supercharger was needed?
What can BB&CE do as sort of a parallel development for a light weight fighter?
And is 355-365 mph at 12,000ft going to interest the US (or Britian or other allied nation) in 1943 for delivery in 1944?
The US was a tough market to sell in, by late 1943 there was no real aluminum shortage, and they didn't know what to do with P-39s and P-40s rolling off the assembly lines.
P-39 & P-40 production lines were already built/equipped and had trained workers. Setting up a new production line for BB&CE's aircraft was not going to save much money unless they built a lot of them.
The J 22 is claiming a useful load of about 1800lbs.
A P-40L is claiming a useful load of 1635lbs. and that is four guns, 201rpg and 120 US gallons (454liters) of fuel. US figured armor/bp glass and radios into the empty weight. I don't know what the Swedes did.