JKim
Senior Master Sergeant
Superb work on the interior!
<> **** DONE: 1/32 Corsair F4U-1A - WW1 / WW2 over Water.
- Thread starter turbo
- Start date
- Thread starter
- #62
turbo
Staff Sergeant
Thanks for the kind words guys! 
Time to get started on the P&W R-2800 Double Wasp radial engine. An awesome power plant and the reason for the Corsair's gull wing design (to accommodate ground clearance for the engine's large prop without making the landing gear too long). I've decided to represent the ignition wire conduits as they should be nicely visible through the cowl, so the first step was to drill holes at the spark plug locations. The cylinders were then painted Citadel Ironbreaker and given an oil wash.
Holes were also drilled in the outlets of the ignition harness before it too was painted Citadel Ironbreaker. 0.3 mm copper wire was then glued into the drilled out outlets with CA.
Thanks for dropping by guys.
Time to get started on the P&W R-2800 Double Wasp radial engine. An awesome power plant and the reason for the Corsair's gull wing design (to accommodate ground clearance for the engine's large prop without making the landing gear too long). I've decided to represent the ignition wire conduits as they should be nicely visible through the cowl, so the first step was to drill holes at the spark plug locations. The cylinders were then painted Citadel Ironbreaker and given an oil wash.
Holes were also drilled in the outlets of the ignition harness before it too was painted Citadel Ironbreaker. 0.3 mm copper wire was then glued into the drilled out outlets with CA.
Thanks for dropping by guys.
Airframes
Benevolens Magister
Good stuff - should look the biz when it's done.
JKim
Senior Master Sergeant
Great start on the engine!
Crimea_River
Marshal
Yep, looks real nice.
Lovely work so far!
- Thread starter
- #68
turbo
Staff Sergeant
Quick update - cylinders, push rods, intake and exhaust pipes dry-fitted. Some push rods require minor adjustment when glued but as always fit is good.
Ignition harness with conduits installed from post #62 fitted to assembly
Next step is to plumb it something like this:
More pics later after a wire cutting and bending session!
Ignition harness with conduits installed from post #62 fitted to assembly
Next step is to plumb it something like this:
More pics later after a wire cutting and bending session!
Robert Porter
Senior Master Sergeant
Tony Hill
Tech Sergeant
Wow!
Crimea_River
Marshal
Wow indeed.
SANCER
Senior Master Sergeant
Awesome work Kirby! 
The cleanliness, the order and the excellent way of applying the paint. My favorite sections in modeling: the cabin, the engines and the undercarriage ... and in your Corsair they are being a pleasure to enjoy your progress!
Sigo atento y felicidades amigo
Luis Carlos
The cleanliness, the order and the excellent way of applying the paint. My favorite sections in modeling: the cabin, the engines and the undercarriage ... and in your Corsair they are being a pleasure to enjoy your progress!
Sigo atento y felicidades amigo
Luis Carlos
vikingBerserker
Lieutenant General
Beautiful work!
JKim
Senior Master Sergeant
Engine is looking great! Don't forget the little pipe that extends from the bottom of the crank case.
Good work so far!
- Thread starter
- #77
turbo
Staff Sergeant
Thanks for the kind words everybody and thanks for the complements Luis, Lo aprecio mucho amigo 
The positioning of the ignition conduits went better than I thought. Additional holes were drilled in the overhead baffle plates to accommodate the conduits to the rear of the cylinders as per the reference photos. Wires were then cut to approximate length and manoeuvred into place with tweezers. After fixing into position if necessary with a small dab of CA, wires were toned down with matt varnish and a dark oil wash to approximate the colour of the real conduits. The gear reduction housing with magneto and distributors was then attached to the front.
Painted the exhausts and firewall and test fitted the engine. Did a bit of work with Tamiya rust pigment on the exhausts although it doesn't show up terribly well in the photo.
Thanks John, I did miss that and didn't see your post until after I'd taken these photos. Attached now
Summer holidays just about over so progress might slow considerably now
The positioning of the ignition conduits went better than I thought. Additional holes were drilled in the overhead baffle plates to accommodate the conduits to the rear of the cylinders as per the reference photos. Wires were then cut to approximate length and manoeuvred into place with tweezers. After fixing into position if necessary with a small dab of CA, wires were toned down with matt varnish and a dark oil wash to approximate the colour of the real conduits. The gear reduction housing with magneto and distributors was then attached to the front.
Painted the exhausts and firewall and test fitted the engine. Did a bit of work with Tamiya rust pigment on the exhausts although it doesn't show up terribly well in the photo.
Thanks John, I did miss that and didn't see your post until after I'd taken these photos. Attached now
Summer holidays just about over so progress might slow considerably now
fubar57
General
Very nice looking engine Kirby. Love the look the Ironbreaker paint gives. I use it on landing gear struts and wheel hubs as well
JKim
Senior Master Sergeant
Beautiful work on the engine! Sigh... I envy you having fun at that scale. I think I need to do another 1/32 kit soon!
