GB-62 1/72 Spitfire Mk 21 Contraprop - Spitfires

Ad: This forum contains affiliate links to products on Amazon and eBay. More information in Terms and rules

PlasticHero

Senior Airman
413
825
Jul 31, 2019
Pennsylvania, USA
Username: PlasticHero
First Name: Alan
Category: Intermediate
Scale: 1/72
Manufacturer: Special Hobby
Model: 72318
Extras: JB Models 1/76 Landrover

I have been looking forward to this build for quite a while. You may have noticed that I am a complete Spitphile and back in the 80's I built K5054, the prototype Spit and this will represent if not the "last" one, at least the most developed. These were introduced very late in the war and did see service but in a very limited fashion. The schemes I have are post-war commanders' aircraft and I am probably going to do an overall silver that will contrast with the typical camo.
cover2.jpg
mk21a.png

Thanks fubar57 fubar57
A very quick look at the plastic shows good detail and not an overly complex build. I'll go into this more as I start glueing.
sprue1.jpg
sprue2.jpg
sprue3.jpg

I'd like to introduce two potential builds for the far future GB's. We have Mustang and Spitfire, how about Me 109 A-Z and then..... Zeros for Heros.

Decided to add a Landrover to this build. I don't know if this aircraft lasted until LR was used but I'm not going to waste a $3 kit when the times lines are "close enough".
 
Last edited by a moderator:
Great to see a Mk.21 in the GB, and I wish there was a full, injection-moulded kit in 1/48th scale.

However, as far as I'm aware, there was only one Mk.21 converted to trial a contra-rotating prop, Serial No. LA218.
I presume that the extra prop blades in the kit are for the Seafire variant, given that there's also an alternative "hooked" tail assembly shown.
 
Thanks Geo, got that.
I haven't checked further for other airframes in the Mk.21 series converted to contra-prop, but as far as I'm aware, this fitting was on trials aircraft (possibly for Seafire development), and I don't think saw service apart from that.
 
The instructions say "Several machines were equipped with Griffon 85 and contra rotating props. It was necessary to enlarge the rudder area." These were test A/C and not in combat service. After the war they tended to be used by higher ranking officers.
(added details to first post)
 
Last edited:
Any thoughts on cockpit color? I want to go with interior green because the black will hide all the detail. Minister of Procurement; "Paint the cockpits with this new black, it's cheaper". Crew Chief; "But it will look awful when the kids build the model." Here is the sprue for the Land Rover; it is the same mold as the Airfix Land Rover.
(new info) Based on the grill shape and location of headlights in the outer fenders, this is a late model Series IIa released in 1969. So not correct for early 50's.
landrover1.jpg

This has 4 small clear bits for the windows and a tiny decal sheet of id numbers. I have not yet found a picture of this exact model in RAF service, but SaparotRob SaparotRob wants trucks with my airplanes sooooo here ya are!
Next GB. Airplanes and their trucks.
 
Last edited:
I found this great model build Vexillum Militaris - Supermarine Spitfire F Mk 21 – Build and will be looking very closely at his wheel angles, shape of the undercarriage doors, radiator profiles and all other minutiae involved with this build. Just kidding, unless there is something that is crucial, obvious, and within my skill set. The wheels are inner and outer halves but all of them have a post rather than post and hole.
wheel1.jpg
wheel2.jpg

The other thing I noticed is it does have TINY pins and holes to line parts up. There are only a few but they do the trick. The lower wing has large ejector pins to remove, and the other parts build up the wheel well. I have them in and they give a lot of detail in there. Instructions call for that to be painted medium sea gray. Don't forget to do the tail wheel area too.
sprue4.jpg

Remember that roundels on the wing go on top of the walkway lines. ℹ️
 

Users who are viewing this thread

Back