Andy, I brushed it on, which normally gives a really good gloss finish, even with just one coat, and a glass-like finish with two or more coats. You'll be able to see what I mean in the pics. I also noticed that it 'blooms' at the slightest touch of even a drop of Micro Sol, which can be seen around the 'R' on the rear, port fuselage. Fortunately, this seems to fade when rinsed with clean water, and will disappear once a sealing coat is applied, and then the final, matt, clear coat.
So, on with the progress report.
All of the main decals are on, which is described below, and the main stencils will be added, using some spare Academy P-47 decals, including some that came with the first of the Arii kits I bought. I'll also try to use some of the Monogram stencils, from the decal sheet left over from a P-47 I built around about 1978 or '79!
Once that's all done, some of the 'paint wear' and weathering will be toned down, as will the yellow 'mission tally' markings, and further 'surface work' will be done after the matt clear coat.
PICS 1 to 3 Show how the model looks so far, and the uneven finish of the Klear (Future) is quite evident, making it look somewhat rough. Fortunately, experience has shown that this should be rectified, once sealed and then topped with the matt clear coat.
PIC 4. First thing to notice is that the moulded-on pitot tube finally succumbed, a victim of another bl**dy shoulder spasm! This 'star and bar' is from the 1976 kit and. although it eventually settled down, not only is there a register problem, which will need to be re-touched, but there's also a flaw in the printing, showing as a 'lump', which is actually an area of heavier ink. Hopefully, this won't be as noticeable once matt coated.
PIC 5. That Monogram decal sheet from all those years ago. The decals are still usable, but they're from an era when they were thick, and with a cloudy carrier film. I tried using the over-sized 'stars and bars' for the underside of the wing, but they would not lie down, so I had to resort to the 'standard' size, often seen, sometimes with a mix of these and 'over sized', and these were sourced from an Otaki Corsair kit sheet, from the early 1980's. Surprisingly, they were the best of the lot, and lay down and conformed without problems and without using Midcro Sol.
I had planned to use the Monogram fuselage decals, or some spare Academy P-47 fuselage decals, both of which have the 'cut out' and separate, small bar section, to fit around the intercooler doors, but, having checked the positioning of the bars, in relation to the AEAF stripes in the photos of the actual aircraft, it transpired that whoever painted the stripes on B8-R, appears to have painted the rear, white stripe, slightly wider than normal, aligning it's aft edge with the rear of the bar to the star. If I'd used the available decals, the aft bar would have protruded beyond the white strip, as seen on most (but not all) P-47s. Consequently, I had to use some decals of the correct diameter, from an ICM Mustang kit, and cut the forward bar to fit as per the photos, whilst aligning the rear bar accordingly, and this will mean painting-in the 'missing' bits once the decals are set and sealed.
PICS 6 and 7. The tail numbers were applied individually, referring to the photos for exact positioning, and were from a brand new Aeromaster sheet. Excellent decals, which came of the carrier sheet and positioned without hassle, this being done by brushing each individual letter with water, then transporting to the model on the tip of a scalpel blade, and sliding into position with a wet paint brush.
Note the angle of the 'R' code letter - this being the first decal applied, and from a Microscale sheet I've had for at least 25 years, probably longer. It immediately stuck like sh*t to a blanket, and the slightest touch was causing it to tear, as it would not move on the 'Futured' surface. I had to leave it as is, as I only had two letter R's left, including this one. The only other alternative would be to remove it, and try to fabricate the letter from a letter 'P', and a piece of white decal from another letter. However, in the photo of this aircraft, it looks like the letter is actually slightly out of true, and also not exactly pristine in shape and appearance, although I'll admit, some of the effect is the angle, and quality, of the photo.
What do you think guys - leave it, or fabricate a new letter?
What looks like slight silvering around the letter seems to have been 'bloom' from the Micro Sol, as it rinsed off, and it might have been a reaction to this and the Future, which caused the decal to 'grab' and stick fast. I din't use any more Sol on the other lettering, but did under the fuselage and upper wing stars and bars, where any clouding can't be seen.
PICS 8 and 9. Research showed that the 'Mission Tallies' on this Squadron's aircraft were painted in the form of 'five bar gates', with four vertical bars and a diagonal 'hatch' denoting five missions. One photo of one aircraft showed these in what appeared to be white, as did a colour profile, although this could well have been the lighting. However, a closer inspection of a couple of other photos of different aircraft, suggested a darker colour, possibly yellow, which was common on bombers, at least. These pics included the subject of the profile mentioned, where the bars and stroke were definitely a darker colour than white, and showed a marked contrast against other white markings on this aircraft. Also, I noticed that the same profile artist seemed to have a couple of other details wrong, including the colour of the rudder trim tab - which was painted in the colour of a different squadron!
As a result, I decided to go with yellow, and trimmed some 'straight' yellow bars from an old B-25 decal sheet - again at least 20 years old. The diagonal 'hatches' were added from thin slivers trimmed from large yellow panels from a Luftwaffe F-4 Phantom sheet, yet again, around 20 or more years old!
The black panel with pilot and ground crew details, fortunately only partly legible, but effective enough, came from the spares box.
So, next step is to tackle the stencils, and touch-up and small detail painting
Although it doesn't look as harsh 'in real life', the gloss coat has really emphasised some areas of paint fade, chipping and dirt, so this will be subdued after the clear, sealing coat, and further subtle weathering/wear added later.
Thanks once again for your complimentary remarks and encouragement, and I hope you all have a great Christmas, wherever you are, and whatever you're dong (Jan, get out of the pub - the Turkey's burning!).
Next up-date will probably be in a couple of days, as I'm going to the pub tonight, and I've also been invited to the pub Landlord's place for Christmas dinner - so no sense from me for a day or two!